Thanks, Chris! Much appreciated!
-
Welcome to the Project Runs Forum!
This forum is intended for interest gauging and active runs. Due to the transient nature of this forum, please keep all research and ongoing discussion in one of our main forums so your information is not lost.
Only Premium Members can start a new run.
Interest DaveP's V2 and V3 run - 2024
Black Ninja
Active Member
Dave can you please check your PM when you get a chance, cheers buddy.Thanks, Chris! Much appreciated!
Hey Dean. I saw your message (eventually) and have replied
Cheers.
Hello there!
Wishing you all a wonderful May The Fourth! I hope you all have a great day and manage to fit in at least one SW movie!
I just wanted to drop in with a brief update on the run.
I am very nearly done painting. Just adding the finishing touches before de-stencilling and final assembly!
I’m hoping to have Batch 5 completed this week still, all being well.
I have begun work on assembling the clamps for this batch and they’re looking great:
I’ll post another update once I have Batch 5 finished and ready to send out.
Parts for the additional batch of V2s are now officially “In Production” and I’ll be listing these on the store for pre-order later today
(12:00 - Midday – UK time)
I previously referred to UK time as GMT. THIS WAS INCORRECT. Sorry for any confusion. The UK is now on BST (British summer time). So GMT+1hr.
I have tried my best to keep the price as close to the original price as possible, but with the passage of time / inflation as well as the updated specs on the machining, there has been a slight increase to the pre-order price unfortunately. (£265)
I hope that’s ok. On the upside, this should significantly lower waiting times for commissions going forward.
As before, the pre-order price covers all parts that are included in the DIY kit:
As always, this is payable upon completion of the work and a separate invoice will be sent out closer to the time to cover painting/weathering and shipping.
I'll be listing a limited number of DIY kits for Pre-Order too. These will be sent out as soon as I receive the parts.
Just a very brief update this week if that’s ok...
I will be back with another one soon (on completion of Batch 5).
I’m looking forward to sharing more images of finished commissions which is always exciting!
For now though, wishing you all a fantastic May The Fourth!
All the best and MTFBWY!
Dave
Wishing you all a wonderful May The Fourth! I hope you all have a great day and manage to fit in at least one SW movie!
I just wanted to drop in with a brief update on the run.
I am very nearly done painting. Just adding the finishing touches before de-stencilling and final assembly!
I’m hoping to have Batch 5 completed this week still, all being well.
I have begun work on assembling the clamps for this batch and they’re looking great:
I’ll post another update once I have Batch 5 finished and ready to send out.
Parts for the additional batch of V2s are now officially “In Production” and I’ll be listing these on the store for pre-order later today
(12:00 - Midday – UK time)
I previously referred to UK time as GMT. THIS WAS INCORRECT. Sorry for any confusion. The UK is now on BST (British summer time). So GMT+1hr.
I have tried my best to keep the price as close to the original price as possible, but with the passage of time / inflation as well as the updated specs on the machining, there has been a slight increase to the pre-order price unfortunately. (£265)
I hope that’s ok. On the upside, this should significantly lower waiting times for commissions going forward.
As before, the pre-order price covers all parts that are included in the DIY kit:
- V2 Body Section (drilled and tapped)
- V2 Emitter/Nipple (pre-damaged)
- V2 Pommel
- V2 Stainless Steel D-Ring
- Replica Michel thumbscrew / Cone knob
- Vintage Boot Stud
- Replica Graflex Clamp
- V2 Lever
- SlothFurnace V2 Clamp Card (Vintage Finish)
- Internal rod/bearings/fixings
- Vinyl Stencil kit
As always, this is payable upon completion of the work and a separate invoice will be sent out closer to the time to cover painting/weathering and shipping.
I'll be listing a limited number of DIY kits for Pre-Order too. These will be sent out as soon as I receive the parts.
Just a very brief update this week if that’s ok...
I will be back with another one soon (on completion of Batch 5).
I’m looking forward to sharing more images of finished commissions which is always exciting!
For now though, wishing you all a fantastic May The Fourth!
All the best and MTFBWY!
Dave
Hey everyone! May the 4th be with you.
Just got a chance to open up my V1 Hero in the “Cave Scene” look in which I I opted for copper rails, and my V2 in the “Throne Room” look. These are absolutely stunning. Dave’s attention to detail is unmatched. Hopefully if there’s a future run I’ll pick up a V3. Cheers to everyone who picked up his work of art this run, and anyone on the fence in the future - DEW IT!
MTFBWY
Just got a chance to open up my V1 Hero in the “Cave Scene” look in which I I opted for copper rails, and my V2 in the “Throne Room” look. These are absolutely stunning. Dave’s attention to detail is unmatched. Hopefully if there’s a future run I’ll pick up a V3. Cheers to everyone who picked up his work of art this run, and anyone on the fence in the future - DEW IT!
MTFBWY
Attachments
KarlBud420
Sr Member
Dave - Just ordered a V2 commission on your site. May the 4th be with you!
Bruce
Bruce
Ugh… was at work all day yesterday and could not get the payment to go through…
Tried again today and the kits are sold out
If you happen to stumble upon more parts for a kit, I’d love to pick one up!
Sean
Tried again today and the kits are sold out
If you happen to stumble upon more parts for a kit, I’d love to pick one up!
Sean
Thanks so much for sharing, Adam! So pleased that you're happy with them!
Thank you SO much! Looking forward to working on this for you! M.T.F.B.W.Y!
Hi Sean! Sorry about that. I allocated a few of them to DIY kits but reserved most of them for commissions. I've just swapped one over though, so should be showing as in stock again if you'd still like to take one.Ugh… was at work all day yesterday and could not get the payment to go through…
Tried again today and the kits are sold out
If you happen to stumble upon more parts for a kit, I’d love to pick one up!
Sean
A huge thank you to everyone who has jumped on this extra batch of V2s, and to those who picked up the last of the V3s. Can't tell you how appreciative I am of your support!
It's been a very productive couple of days and looking forward to sharing some more finished commissions in the next update!
All the best and M.T.F.B.W.Y!
Dave
Similar threads
- Sale
